Really? I never knew any of them were synchronized, that’s cool if so. I seem to remember us pulling them off the wall at our schools and changing them twice a year or replacing the batteries. Having them wired with synchronization may be overboard, but it is kind of cool
All my schools had them. Sometimes you’d catch them doing a resync and all the hands would spin around. I think they probably couldn’t rotate CCW so had to go around the long way if they needed to roll back a few minutes.
Yes I remember sometimes they would remotely adjust our clocks and you could see the hands moving quickly until they stopped in their intended position. Pretty genius for the old days.
Could they be synchronised independently?
My grandfather in France had a clock that was receiving a radio signal I think from Strasbourg.
They’ve been around for a while.
I remember being up late during day light hour change and i would suddenly hear the second hand rush forward.
It would stop one whole hour on the switch back.
I would use it to adjust my watch.
Nowadays I use raw GPS and any mobile phone is synced from the network anyway.
My highschool was small (graduating class under 50; five small towns combined), and in the 90s, ours were synchronized, just realized I always wondered what they used.
Thank you, I’ll need to look into it, it was obvious they were synced because they got adjusted for daylight savings from somewhere and they all slowly changed time over the course of an hour if I recall correctly, it always fascinated me.
Would that not mean if the power goes out after say a hurricane, the all the clocks have to be reset manually or can they somehow change them all remotely? A mechanism going threw the walls to change them from a single location sounds like a lot of work to get a synchronized clock
At what point is it not just a digital clock with an analog interface if it has the ability to receive information digitally and perform tasks off of it. (I assume increase/decrease voltage to the motor).
Unless maybe that’s how they do it, put all the clocks on an individual power source, then manipulate the current to increase/decrease the speed of the motors so they all move synchronized… Idk, cool concept though. Not sure how you would overcome the loss in varying distance of the clocks though… it’s possible but a lot of planning
Its the Hertz of ac current that comteols timing. But that’s just how it counts the seconds not how it would tell if it is noon. But its uses analog electricity to keep time and maybe a digital comand to set time. Does make it digital or analog?
I was thinking if you had a set voltage and resistance you could hold a certain rpm for the motor going to the gears. Then if you needed to adjust it you could stop the current by dialing down the voltage or possibly increase the analog dial to increase the voltage and make the clocks motors all spin faster until you reached the desired time and dial it back to standard voltage. But you would have loss over distance in the wire unless you made them all the max length needed, and coiled them to make them all the “same length” from dial to clock.
Really? I never knew any of them were synchronized, that’s cool if so. I seem to remember us pulling them off the wall at our schools and changing them twice a year or replacing the batteries. Having them wired with synchronization may be overboard, but it is kind of cool
All my schools had them. Sometimes you’d catch them doing a resync and all the hands would spin around. I think they probably couldn’t rotate CCW so had to go around the long way if they needed to roll back a few minutes.
Yep. The schools I went to had synchronized analog clocks. They would all “adjust” together if they were off at all. Some kind of clockwork solenoid.
Yes I remember sometimes they would remotely adjust our clocks and you could see the hands moving quickly until they stopped in their intended position. Pretty genius for the old days.
Could they be synchronised independently? My grandfather in France had a clock that was receiving a radio signal I think from Strasbourg. They’ve been around for a while. I remember being up late during day light hour change and i would suddenly hear the second hand rush forward. It would stop one whole hour on the switch back. I would use it to adjust my watch. Nowadays I use raw GPS and any mobile phone is synced from the network anyway.
My highschool was small (graduating class under 50; five small towns combined), and in the 90s, ours were synchronized, just realized I always wondered what they used.
Probably the clocks all used a synchronous motor. It spins baaed on ac current. After juat set the clocks to the right time when you plig them in
Thank you, I’ll need to look into it, it was obvious they were synced because they got adjusted for daylight savings from somewhere and they all slowly changed time over the course of an hour if I recall correctly, it always fascinated me.
Would that not mean if the power goes out after say a hurricane, the all the clocks have to be reset manually or can they somehow change them all remotely? A mechanism going threw the walls to change them from a single location sounds like a lot of work to get a synchronized clock
Im sire there is. A way to send a comand to clockw to fast-forward to a certain time.
At what point is it not just a digital clock with an analog interface if it has the ability to receive information digitally and perform tasks off of it. (I assume increase/decrease voltage to the motor).
Unless maybe that’s how they do it, put all the clocks on an individual power source, then manipulate the current to increase/decrease the speed of the motors so they all move synchronized… Idk, cool concept though. Not sure how you would overcome the loss in varying distance of the clocks though… it’s possible but a lot of planning
Its the Hertz of ac current that comteols timing. But that’s just how it counts the seconds not how it would tell if it is noon. But its uses analog electricity to keep time and maybe a digital comand to set time. Does make it digital or analog?
I was thinking if you had a set voltage and resistance you could hold a certain rpm for the motor going to the gears. Then if you needed to adjust it you could stop the current by dialing down the voltage or possibly increase the analog dial to increase the voltage and make the clocks motors all spin faster until you reached the desired time and dial it back to standard voltage. But you would have loss over distance in the wire unless you made them all the max length needed, and coiled them to make them all the “same length” from dial to clock.